InstructionsModels MGFP39/44/49Equipped with Safety Pilot System / Remote Control ValveDo not store or use gasoline or other fl ammable vapors and liqu
8Supporting Floor Systems It is the ultimate responsibility of the installer to ensure that proper concrete slab supports are used.WARNING to the lice
9MASON-LITE Weight DeterminationThe following are dead load weight estimates for the Mason-Lite Fireplace.Table IFireplace ModelMGFP39 MGFP44 MGFP49Fi
10ATTENTION: Figure that these totals for the dead loads are in addition to the actual live load as well as other dead load requirements for the speci
11Fireplace Assembly ProceduresFireplace Assembly ProceduresPlace the Mason-Lite fi replace hearth on the fl oor where the fi replace is to be installed.
12Install Downdraft Diverter and fi nal row of Side Walls (Figure 17). Then place #3 rebar (8 each, 36 inch long) vertically through the cells until th
13Mason-Lite Firebrick LinerThe fi rebrick lining is not supplied as part of your Mason-Lite fi replace but can be purchased from MFI. They are availabl
14Caution in Regards to Combustibles – If any part of the fi replace or objects in the room (curtains, rugs, paint, cushions, etc.) start to show warpi
15MASON-LITE once installed is 14’0” (fourteen feet) and that it is higher if offsets are used. Here is how to calculate the height of the completed fi
16 A “B-type” venting system must be connected to the appliance for venting to outside of building. The following section is provided as a guide to a
17Specifying Chimney HeightsSpecifying Chimney Heights If the horizontal distance from the mid-point of the chimney to the peak of the roof ridge is
THIS PAGE INTENTIONALLY LEFT BLANK
18Figure 27Vent Plate InstallationAttention: Clearance to combustible construction can not be reduced during course of construction. For the safe oper
19CAUTION: Use only the logs that come with this gas fi replace. The manufacturer cautions against using chemical chimney cleaners. Never burn solid f
20Placing the LogsPlace the back bottom log on the grate behind the top burner and as far forward (against the top burner) as possible without touchin
21TO LIGHT THE FIREPLACE WITH THE WALLSWITCHMove the ON-REMOTE-OFF wall switch to the ON position (Figure 41). This transmits a rapid series of sparks
22Maintenance Once installed and operating properly, the Mason-lite gas fi replace requires very little maintenance. You should inspect the fi repl
23Appendix IFor installations regulated by the International Residential Code, the support foundation for the fireplace installed on concrete shallcon
24Appendix IIFIGURE R301.2(3) WEATHERING PROBABILITY MAP FOR CONCRETEa. Alaska and Hawaii are classified as severe and negligible, respectively.b.
Limited WarrantyMason-Lite™ Fireplace Masonry Fireplaces Industries, LLC (MFI) warrants all MASON-LITE Fireplaces to be free from defects in materials
1Contents ...Pg
2Fireplace Parts ListFireplace Parts ListSee Page 8 and 9 for framing anchoring components.WARNINGFailure to position the parts in accordance with the
3* ITEMS NOTED ARE SOLD SEPARATELY.ITEMS INDICATED AS “NOT SUPPLIED” CAN BE OBTAINED FROM YOUR LOCAL HARDWARE STORE.Optional Outside Ø4” Combustion Ai
4Burner & Logs Parts ListBurner & Logs Parts ListITEM P/N DESCRIPTIONQTY1GMLB-39/44-01(P)GMLB-49-01(P)Pilot, Burner assembly12RR-1ARemote tran
5Product OverviewIntroduction We extend a warm welcome from all of us at Masonry Fireplace Industries, LLC. (MFI), proud manufacturers of Mason-Lite
6Required Gas Pressure The minimum inlet gas supply pressure for the purpose of input adjustment is 5” of water column (w.c.) for natural gas. The m
7Clearance to CombustiblesClearance to CombustiblesThe distance to be maintained from the surfaces of the fi replace to combustibles must be observed.
Commentaires sur ces manuels